Moulded and extruded components for sealing, gasketing and vibration isolation, plus custom parts and ready-to-use compounds. Everything is made to your drawing, sample or specification. If it is rubber and it seals, we most likely make it.
Cured under heat and pressure in hydraulic presses, with tooling held in-house. Best for complex geometry, tight tolerances and high repeatability.
Compression and transfer moulded gaskets in Silicone, EPDM, NBR, FKM and Neoprene, 20 to 90 Shore A. For flanges, enclosures and housings that see pressure and temperature cycling. Made to your drawing, or reverse-engineered from a worn sample.
Ready tooling for 10,000+ sizes covering BS 1806, ISO 3601 and metric standards, in every compound we mix. Static and dynamic sealing from -60°C to +230°C depending on polymer. Repeat orders on existing tooling ship fast.
Cable and wire-entry grommets that hold IP67 and IP68 in enclosure walls. Silicone and EPDM standard, with blind closed-membrane types for unused knockouts. We design the interference fit for your panel thickness and hole size.
Over 1,000 standard sizes plus custom dimensions to drawing. Any of our elastomers, 30 to 90 Shore A, with fabric-reinforced grades where bolt loads would crush plain rubber. Volumes from a handful to millions.
Bushes, mounts and machine pads that isolate vibration and spread load, including rubber-to-metal bonded types. NBR, CR and natural rubber blends chosen for your load and deflection. Send the machine weight and footprint and we do the sums.
Rubber vulcanised directly onto steel, stainless or brass inserts — anti-vibration mounts, bonded bushes and sealing plates. Grit-blasted and primed before moulding, so the bond fails in the rubber, never at the interface. Your insert or ours.
Continuously vulcanised to a constant cross-section, cut to length or joined into loops. Thousands of die profiles on hand, new dies cut to your drawing.
Thousands of die profiles on hand: U-channels, D-sections, A- and P-sections, wiper blades, glazing and edge trims. New dies are cut in our own toolroom in days, not weeks. EPDM for weather, silicone for heat and cold.
Closed-cell sponge profiles, cords and strips. Lower compression stress and weight than solid rubber, so lightweight doors and covers still close properly. Densities compounded to your compression-deflection spec.
Extruded lengths vulcanised end-to-end into endless loops. A-type, D-type and P-type sections with a joint as strong as the profile itself, no glue line to fail. Where a loop needs to stay square, we vulcanise mitred 45° corners so the frame holds its shape. The standard fix for enclosure doors that leak at the corners.
Extruded silicone tubing, 1 mm to 40 mm ID, wall thickness held to tight tolerance on the CV line — liquid transfer, gas lines, insulation sleeves and gasketing. Compliant grades for food, pharmaceutical and potable water service: FDA 21 CFR 177.2600, BfR XV, USP Class VI and BS 6920, with documents on every dispatch. EPDM and NBR to order.
Solid cord 1 mm to 25 mm diameter, 45 to 90 Shore A, cut to length or joined into rings — often the cheapest way to seal a machined groove. Flat silicone packing strip under our VINSA brand: consistent section, high tear resistance, service from -60°C to +225°C. Food-grade and heat, oil and acid resistant grades offered; stocked sizes ship immediately.
Our speciality: soft extruded sections down to 30 Shore A in silicone and 40 Shore A in EPDM. Soft enough to seal light doors, thin panels and slightly warped flanges without closure force, and held to section on the CV line where soft compounds normally slump. Where a standard 60 Shore A profile will not close, this is the fix.
When the part or the material does not exist yet. Send us the problem and we engineer the component or mix the compound to match.
Send a drawing, a sample or a description of the problem. CAD, compound selection, tooling and production all happen under one roof, so the first article arrives in weeks. Reverse engineering of imported parts is routine work here.
Uncured compound mixed to your spec and delivered ready for your own presses. Conductive, fire-resistant, self-extinguishing, or an extremely low compression set. We formulate it and prove it on the rheometer before dispatch.
First articles before you commit to a production tool. Soft-tooled and hand-finished rubber prototypes in your chosen compound, and CNC turning and milling of metal parts, inserts and test fixtures in our own machine shop. One piece or fifty, so you can fit it, test it and change it before the hard tool is cut.
Send a drawing, a sample or a description. We will tell you the right material and make it to your spec. Not sure which polymer? Try the material picker. Curious how it gets made? Walk through our process.